Magic Resin

Epoxy vs Polyaspartic Garage Floor: Which Coating Should You Choose?

By Magic Resin•
Epoxy vs Polyaspartic Garage Floor: Which Coating Should You Choose?

Epoxy vs polyaspartic is often the first question when you plan a garage floor coating. In a good floor system, the two products do different jobs. This guide compares them and shows how the Magic Resin floor system uses both.

The short answer: epoxy is the base coat. It bonds to the prepared concrete, carries the colour and holds the decorative flakes. Polyaspartic is the clear top coat. It cures fast, resists wear and chemicals, and does not yellow in sunlight. For a garage with cars, road salt or sun, use both.

What is epoxy floor coating?

Floor epoxy is a two-part coating: a resin (Part A) and a hardener (Part B). Once mixed, they react and cure into a hard, seamless and glossy film that is easy to clean. Magic Resin floor epoxy mixes at 2A:1B by volume. It comes in Clear or Light Grey, in 1.5, 3 and 6 gallon kits.

Epoxy bonds well to prepared concrete, and its longer working time makes it forgiving. Its weak point is sunlight: like most epoxies, it can yellow over time under UV light.

What is polyaspartic floor coating?

Polyaspartic is a type of aliphatic polyurea. It is also a two-part coating, but it cures much faster than epoxy. Because it is aliphatic, it is UV stable and does not yellow. It is also highly resistant to abrasion, chemicals and impacts.

Magic Resin polyaspartic is a clear top coat for use over the floor epoxy, with or without flakes. It mixes at 1A:1B by volume and comes in 1, 2, 3 and 4 gallon sizes. Do not tint it: the pigment goes in the epoxy layers only.

Epoxy vs polyaspartic: side-by-side comparison

Values are for Magic Resin products. Times are approximate and change with temperature and humidity.

Property Floor epoxy Polyaspartic
Job in the system Base coat: bonds to concrete, holds colour and flakes Clear top coat: protects against wear, chemicals and UV
Working time About 25–45 minutes About 15–20 minutes; about 10 minutes in the bucket
Foot traffic After about 24 hours (12 hours at the earliest) After 4–6 hours
Vehicle traffic After about 3 days After about 3 days (full cure)
Application temperature 15–31 °C 10–30 °C, humidity up to 85%
UV and yellowing Can yellow in sunlight over time UV stable; does not yellow
Abrasion and chemical resistance Good Higher
Hot tires Needs good preparation and a full cure More heat resistant; still needs a full cure
Film build Build coat: about 175 sq ft per gallon, per coat Thin clear coat, not a flood coat: about 150 sq ft per gallon (125 over full flakes)
Odour Milder; ventilate Usually stronger; ventilate well
DIY difficulty Easier; more time to correct mistakes Harder; mix small batches and work fast
Cost Lower per gallon Higher per gallon

Cure time, working time and DIY difficulty

Polyaspartic is fast. You can walk on it after 4–6 hours, compared with about 24 hours for epoxy. For vehicles, plan about 3 days with either coating, so the fast cure mainly helps with foot traffic.

The speed has a cost. Polyaspartic gives you about 15–20 minutes of working time, and it starts to thicken in the bucket after about 10 minutes. Epoxy gives you about 25–45 minutes. Heat shortens both, and humidity also shortens the working time of polyaspartic. Mix polyaspartic in small batches, pour it out at once and work with a helper.

Temperature and humidity

Apply floor epoxy when the air and the slab are at 15–31 °C. The polyaspartic instruction sheet allows 10–30 °C, with humidity at or below 85%. Keep the slab at least 3 °C above the dew point. Then let the floor cure for 2–3 days at about 20–25 °C, with humidity below 80%. Keep water and condensation off fresh polyaspartic for at least 48 hours.

UV stability and yellowing

Polyaspartic stays clear in sunlight. Epoxy can yellow over time where sunlight reaches it, for example near the garage door or a window. If your floor gets sun, finish it with polyaspartic.

Wear, chemicals and hot tires

Both coatings resist stains and common spills once they cure. As a top coat, polyaspartic gives more resistance to abrasion, scratches, chemical spills and heat. Magic Resin recommends it for vehicle traffic and heavy use.

Hot-tire pickup happens when hot tires soften a coating and pull it off the slab. The usual causes are poor preparation, an incomplete cure or a thin paint-type product. Good grinding, a full cure before parking and a hard top coat help prevent it.

When to choose epoxy, polyaspartic or both

  • Epoxy only: an indoor floor with little sun and low to medium traffic, such as a basement. Apply two coats, or a clear epoxy top coat over the flakes.
  • Epoxy base coat + polyaspartic top coat: a garage with vehicles, road salt, heavy use or sun. This is the system in Magic Resin floor kits.
  • Polyaspartic over an existing epoxy floor: to add wear and UV protection to a sound floor. Clean and scuff-sand it first. See how to clean and maintain an epoxy garage floor.

How the Magic Resin floor system uses both

Magic Resin floor kits combine a pigmented epoxy base coat, decorative flakes and a clear polyaspartic top coat. Here is the order and timing for a full flake floor:

  1. Prepare the concrete (see the next section).
  2. MVB primer, if needed. Use it when the moisture test fails. Apply the base coat after about 8–10 hours, when the MVB is slightly tacky but mostly dry.
  3. Epoxy base coat. Tint it to match the main colour of your flakes. Pour it out, spread it with a flat squeegee and back-roll it.
  4. Flakes. Broadcast them right away into the wet base coat. For a full broadcast, continue until no wet spots show.
  5. Scrape and vacuum. After about 10–12 hours, scrape off loose or sharp flakes and vacuum.
  6. Polyaspartic top coat. Apply it at least 12 hours after the base coat. Over a full broadcast, no sanding is needed. Squeegee it, then back-roll it with a 3/8-inch short-nap roller. For more traction, broadcast aluminum oxide into the wet top coat.
  7. Cure. Walk on it after 4–6 hours. Park after about 3 days.

The floor epoxy and polyaspartic collection has complete kits for this system: Medium Flake (250 or 500 sq ft), Heavy Flake (300 or 600 sq ft) and Full Flake (300 or 600 sq ft). Each kit includes the epoxy, flakes, pigment, polyaspartic and the main tools, including spiked shoes.

Surface preparation basics

Most coating failures start with poor preparation. Both products need clean, dry and open concrete.

  • Clean: remove oil, grease, salt, dust, old paint and sealers.
  • Grind: diamond grinding is best; acid etching is the other option. If a drop of water beads up instead of soaking in, grind more.
  • Repair: fill cracks, holes and spalls first. The coatings do not fill deep cracks or level a slope. Wait 7 days before you coat over a fresh repair with Magic Resin concrete repair mortar.
  • Dry: vacuum all dust. After any wet step, even a mop, let the slab dry for 24–48 hours. New concrete must cure for at least 30 days. The slab should be below about 4% moisture.
  • Test: tape an 18–24 inch square of clear 6-mil plastic sheet to the slab, airtight, for 24–48 hours with the doors closed. Condensation or darker concrete means you need the MVB moisture vapour barrier primer.

For the full method, read how to prepare your garage floor before applying epoxy.

How much product do you need?

The Magic Resin floor calculator uses these planning rates:

  • Floor epoxy: about 175 sq ft per mixed gallon, per coat.
  • Polyaspartic: about 150 sq ft per gallon, or 125 over full flakes.
  • Flakes (full broadcast): about 20 lb per 125 sq ft. A partial broadcast uses much less.
  • MVB primer: about 115 sq ft per gallon.
  • Pigment: one bottle per 1.5 gallons of mixed epoxy.

For example, a 500 sq ft floor with full flake coverage needs about 2.9 gallons of epoxy (one 3-gallon kit), about 80 lb of flakes and about 4 gallons of polyaspartic. The 600 sq ft Full Flake kit also covers it.

For your floor, enter the area in sq ft or m² in the floor epoxy, flakes and polyaspartic calculator. Choose your flake coverage, top coat and options, and it builds the product list for you.

Frequently asked questions

Is polyaspartic better than epoxy for a garage floor?

It is the better top coat, not a replacement for the base coat. It cures faster, resists wear better and does not yellow. Epoxy gives more working time and holds the colour and flakes. That is why Magic Resin floor kits use both.

Can I apply polyaspartic over epoxy?

Yes. Over a full flake broadcast, wait at least 12 hours and remove the loose flakes; no sanding is needed. Over plain epoxy, wait about 24 hours, then scuff-sand with 180–220 grit and clean.

Can I apply polyaspartic directly on bare concrete?

Not in the Magic Resin system. It goes over the epoxy base coat or the MVB primer. Its instruction sheet warns that, without a moisture barrier, moisture from the slab can cause delamination.

Can I skip the polyaspartic top coat?

Yes, indoors. Floor epoxy can be the final coat. Choose polyaspartic when the floor gets sun, vehicle traffic or heavy wear.

How long before I can park on my new floor?

Plan about 3 days with either coating, at about 20–25 °C.

Can I coat my garage floor in winter?

Only if you can heat the garage and the slab to the application temperatures above, then hold about 20–25 °C for 2–3 days. After a full cure, cold is not a problem.

Before you start, read the instructions and the safety data sheet (SDS) for each product. Ventilate the garage and wear gloves and eye protection. For a large floor, Magic Resin recommends an organic-vapour respirator. For project questions, email contact@magicresin.ca.

Shop All Products