Magic Resin

Art & Craft Resin

The Art & Craft Resin is most suitable for projects requiring pours up to ~3/4" at a time. Cures in ~24-36 hours.

Art and craft resin buying guide

Art & Craft Resin is a medium-thickness epoxy for jewellery, earrings, coasters, small castings and moulds. You can pour up to about 3/4 inch (about 2 cm) per layer. It cures in 24 to 36 hours, depending on the depth.

Is Art & Craft resin right for your project?

Choose Art & Craft resin for moulds and small casts. It is thinner than Table Top resin, so it flows into mould details. It is not made for flat coatings, because it does not self-level like a coating resin.

  • Coatings on tables, artwork or tumblers: choose Table Top & Coating Resin.
  • Paperweights, bouquet blocks and other thick pieces: choose Deep Pour resin, or pour Art & Craft resin in layers.
  • Very small pieces in minutes: UV resin needs no mixing and cures in 1 to 3 minutes under a UV lamp.

Which kit size to buy

Kits come in 16 oz (473 ml), 32 oz (946 ml), 1 gallon (3.78 L), 2 gallons (7.6 L) and 4 gallons (15.2 L). The kit size is resin and hardener together. Most kits include gloves, mixing cups, stir sticks and 5 g mica powder packets. The 2-gallon kit is also sold without accessories.

To find the amount, measure the inside of the mould up to the fill line. You can also fill a watertight silicone mould with water and measure that water. Then let the mould dry fully before you pour. Example: four round coasters, 10 cm wide and 1 cm deep, need about 314 ml of mixed resin before losses. See How much epoxy resin do I need? or use the epoxy calculator. Browse our moulds for coaster sets and shapes.

Mixing, working time and cure

The quick start guide for this resin is on our instruction guides page. Wear gloves and eye protection, and work in a ventilated room.

  • Mix ratio: 1:1 by volume, or 100A:90B by weight.
  • Room: 20 to 25 °C (68 to 77 °F), with 40 to 60% humidity. Warm cold bottles in warm water first.
  • Mix slowly by hand for 4 to 5 minutes and scrape the sides. Do not scrape the cup when you pour.
  • Working time: about 30 to 45 minutes.
  • Bubbles: pass a torch quickly over the resin. Do not touch silicone moulds with the flame.
  • Next layer: pour it when the layer is tacky but a fingernail still dents it, usually after 8 to 16 hours. If the layer has fully cured, sand it with 180 to 220 grit.
  • Cure: 24 to 36 hours. Wait one week before items such as coasters get regular use.

Frequently asked questions

Can I pour more than 3/4 inch at a time?

Pour in layers instead. Wait until the layer is tacky, usually 8 to 16 hours, then pour the next one. For a thick piece in one pour, use Deep Pour resin.

Can I put dried flowers in the resin?

Yes, if they are fully dry. Fresh flowers hold water. Test a spare petal first, then set the flowers in a thin first layer. Read how to preserve dried flowers in epoxy resin.

How much mica powder do I need?

Up to about 125 g per gallon of mixed resin, but 50 g is often enough. Add it little by little. Mica gives an opaque shimmer. For a see-through look, use translucent pigments. Read how to colour epoxy resin and see our pigments.

Why are there bubbles in my piece?

Common causes are fast mixing, cold resin and air trapped in mould details. Warm cold bottles, mix slowly and pass a torch quickly over the surface. See 10 tips to eliminate bubbles.

How do I clean my silicone moulds?

Remove cured bits gently, wash with warm water and a little mild dish soap, rinse and let the mould dry fully. Do not use blades or scouring pads. Read how to clean and care for silicone resin moulds.

Customer Reviews & Photos

Shop All Products